Filter tubes
shown is only a smal selection of possibilities and sizes
Info: filter tubes Lenght of the white tube is NOT the same value as max filling high!
|
||
![]()
|
Filter0005 360,-€ |
smal filter with p-port fitting caps size internally 110mm size externally 121mm lenght of white tube 220mm (means aprox 175mm max filling) (Lids 4mm plus fittings (p-port or custom wish) on these small tubes an integration of sensors to the head is NOT possible! Aprox 1,5 kg max filling on this size
lower mesh is fixed into the tube filling high is flexible
|
![]() |
Head lid for Filter 0005 Also on the small 120mm scrubber a 90 degree p-port fitting is possible NO sensors inside are possible on the small size |
|
![]() |
Filter0010 390,-€ |
big filter with p-port fitting caps size internally 138mm size externally 150mm lenght of white tube 200-220mm (standard) (Lids: 4mm plus fittings (p-port or custom wish) On this size max filling is around 2.1 to 2.3 kg of sorb depending on which brand is used |
Scrubber load calculation sample: most sorb has a density of aprox 870 to 900g/l (Dräger, 797 e.g) Lenght of white tube: 220mm makes max filling high 175 mm internal diameter: 138 mm theoretical max load: 2,35 kg of sorb ------------- 200mm lengh gives 155mm filling high, with 138mm diameter max theoretical load: 2,07 kg of sorb |
Several other sizes are possible on request standard fitting is the male p-port, straight version as seen on Filter0005 Lenght of white tube is normally 200-220 Possible combinations : 110/121 120/131 130/141 138/151 (standard)
|
|
![]() |
260,-€ |
End cap with integrated closed 3 cell house works with filters of 150mm external diameter only
The male p-port and the head have a mark (red on the picture). The mark on the male p-port shows position of center sensor. Lid stays 28mm out of scrubber Due to construction with this lid the max filling high of the tube is reduced by 10-12mm to ensure good gas flow For max filling lid must be thicker, aprox 40mm outside the white tube
|
![]() |
Filter 0050 450,- |
filter size internally 138mm size externally 150mm lenght of white tube standard 200-220mm Left lid plus 4mm righ lid with male p-port 90 degree is 52mm No sensor holder |
pic follows |
Filter 0051 490,-
|
same as Filter 0050 both end cap with male p-port 90 degree o top
|
pic follows |
Filter 0060 550,-
|
similar to Filter 0051 with water trap and OPV to drain in exhale side clips for 3 sensors in inhale side
|
![]() |
Lid for Filter 0050/51 can be upgraded with internal 3
cell holder, position of cable gland can be choosen Sensor holder upgrade 50,- Euro
|
|
![]() |
Filter 0020 440,- Euro
|
For double scrubber on the shoulder
ideas..... both end caps have internally conical shape
smal filter with female p-port fittings at 45 degree size internally 120mm size externally 140mm lenght of white tube 185mm (140mm filling ) overall lenght with both caps 280mm
Aprox 1,4 kg max filling on this size lower mesh is fixed into the tube filling high is flexible
|
![]() |
Filter 0025 550,- Euro |
For double scrubber on the shoulder ideas.....with sensors integrated... same dimensions- as Filter 0020the filter contains an internal 3 cell holder and is ment to be used on divers left shoulder as only then the sensors are facing downwards and possible condensate falls down
For such a scrubber couple all end caps can be used at any side of the filters, just if a sensor head is used it must be left shoulder. (as seen on the pic above)
|
![]() |
Filter 0100 450,- Euro |
Filter "Ray style" lenght with lids (wirhout p-ports) 260mm
inner diameter 138 mm outer diameter 150mm aprox 2.2 kg of sorb, partial filling possible |
If you need other combination not listed here, just e-mail -- martin@tecme.de |
||
Alle Preise, die auf der Webseite
angegeben sind verstehen sich inklusive der gesetzlichen MwSt. und zzgl
Versandkosten Für unsere Waren bestehen die gesetzlichen Gewährleistungsrechte |