210,-€ 

SCRUBBER CARTRIDGE for refilling
max filling with the small 797 is 2,3kg

weight empty: aprox 920 gramm

NEW: a more comfortable handle from stainless steel rope for top mesh to get it out
(Picture left side)

due to high requests  there may be delays in shipping them out...first come first serve...

42,- €

Poseidon BOV chin holder

easy to install and strong clip on version

very comfortable while using a scooter, when a NERD is installed, for CM units...and so on

19,-€

It only fits replacement hose adapter, used on left side hose connection only

can NOT be used with original hoses as here the nut can not be replaced.

19,-€

Made to fit only original Poseidon nut, to be used on left side of mouthpiece

check the pdf for more details how to clip in on

Pos_Nerd_clip.pdf

PSR 11 39 MD3

85,-€ 

245,-€

T-piece with integrated single cell house and 3/8 UNF hole for gas injecting

House is made from one solid block of course

The Solid State Sensor Cpod fits also

98,-€ 

price for t-piece, cable is extra

is for PSR 11 39 MD3/MHD cells, so the same as the unit itself uses

T-piece- including lid and cable gland

set with o-rings

20,-€

set of cap and the two o-rings

bag_cpod

price is without CPOD

price per 1 piece without cpod

to install a CPOD holder instead of an APEKS OPV for example

145,- € 

cable lenght can be up aprox 140cm (plus the lenght of the two wires)

This is ready to install for example to the orig. Poseidon third cell holder
The white shoe will be delivered extra so cable can go through cable gland.
One side is marked with a green piece of cable

62,-€ 

without the 90 degree angle

Easy to connect a hose from a manual add.

196,- Euro

Inletadapter (PD0700), new style 90 degree 3/8 Adapter

Flex-LP hose 30/35cm, Manual add

price is for 1 set as seen in the picture

Feb 2022: New version has now standard BCD nippel installed

as manual add

Ring only: 55,- €

Si Tech inlet valve: 69,- €
(slide, push or skeleton version)

complete set with T-piece 155,- €

195,- € with nut and valve

complete

T-piece for the ATS BMCL

special for for a SI Tech inlet valve,

so it can be used as manual add

does have a watertrap

for more infos check T-pieces for CL´s

245,-€ 

Mounted directly to the head.

This special house seen left side has a p-port fitting, as Ray hoses were used on that particular house

It also can have original thread fitting of course to keep all original hoses

Mounted it looks like this.....

40,-€

55,-€ with nut

the anticollapse part (the lower part) of Poseidon T-piece MUST be cut off!!!

The counter lung itself does have an anticollapse device installed.

50,-€ 

a waterproof plug to close the contacts when Batt is not in,

ideal for transport and shipping to protect electronic pins

95,-€ 

DUST AND WATER cover for Poseidon head

it seals with an o-ring, but is NOT  fixed, so only for transport or storage the unit
if head is taken off to avoid water or dirt to come in

130,-€ 

WATER cover for Poseidon head

a more strong version for better sealing.
A bit thicker and holes for fixing it, holds pressure
 

365,-€  

39,-€ / Set

CALIBRATION KIT for the sensor house

the two plugs also fit also the scrubber and T-pieces of course.

the lower cap has a 2mm hole to avoid over pressure.

one plug does have a 3/8 UNF hole to either add a blind plug
if the plugs are used as blind plugs
or use an inflator coupling when you used as cal kit to inject a O2.

SET -  2 plugs and the cap
(without the inflator coupling)

35,-€ 

FILLING adapter for the M26x2 
O2 tank and other tanks of course

Adapter M26x2 male  --  G 5/8 female (normal DIN)

so use DIN on the new M26x2 valves
(chromed brass)

PD0010

29,-€ / piece

without nut 

shown here for Ray hoses

price is wihout nuts

PD0012

45,-€

JJ-hoses to Poseidon BOV

price per piece, including nut (sample seen left)

PD0013

45,-€ 

40mm-hoses to Poseidon BOV

price per piece, including nut (as seen left) 

PD0013_AP

90,-€ /set of 2

AP-hoses to Poseidon BOV

Various hose adapters to connect different breaththing hoses to the Poseidon DSV

24,-€ / Set

SET - two

47,-€ / Set

SET  -  with 2 nuts

this allows overpressure to scrubber unit!

24,-€ / Set

  These will close the hoses

130,-€ / piece

yes, it can have a drilled/threaded 3/8 UNF hole on one side, centered

140,-€ / piece

as seen here

special wishes are possible, one side or both sides longer

yes, it can have a drilled/threaded 3/8 UNF hole on one side or on both....

185,- Euro 

shown for standard 36mm hoses, other hose conenctors are possible

set of two 70 degree fittings

(price without BOV)

60,-€ 

Adapter to fit a

Panorama FFM  --  the mouthpiece of MK VI

95,-€ 

Adapter to fit a

OTS FFM  --  the mouthpiece of MK VI

60,-€ 

Adapter to fit a

Poseidon Atmosphere FFM  --   the mouthpiece of MK VI

check here

Für unsere Waren bestehen die gesetzlichen Gewährleistungsrechte