Soda Lime

Draegersorb 800 Plus

22,- Euro /4,15 Kg (5l) canister

NEW

Tool for opening and closing the screw from

 Dolphin/Atlantis scrubber

Usefull with cold fingers and thick gloves..and...

20,- €

for DS4 and other regulators

open your regulator without scratches

20,-€

T002b

NEW

flexible Spanner

for DS4 and other regulators

20,- €

Small  22-35     T002a    n/a

Big 35-60         T002b

of course works perfect for DS4 also

T003

NEW

of course made from stainless steel

  7/16 UNF  and 3/8 UNF holder

20,-€

  Due to many wishes a combi holder

Due to many request for smal amounts

O2 Grease, Oxylupe

for 100% O2 High Pressure!

18,- €

aprox. 10 gramm (+/- 0,5)

This O-ring replaces DRA T10612

As some divers have often a problem with flooding at DSV inhale side we offer a slightly thicker o-ring.

This O-ring is a few 1/10 thicker than original

Very limited number as it is special made

4,-€ 

Free Flow Control

50,- Euro

of course it does come including an OP valve for 1.stage

one side 3/8 male, one side 9/16 male

(flow goes 9/16 > 3/8)

58,-Euro

stainless steel with rubber protection

set of 2

Inspiration

Quick fit off board system, tank holder for rebreathers

95,- Euro

comes with two tannk clips

Dwyer Flowmeter

Range 0,2 - 1,2 l/min air

38,-€    (T0012)

or

Range

2,5 - 25 l/ min air for SCR

38,-€    (T0012a)

T0020    Dolphin

T0021    Ray

T0022 CL  KISS

T0023    Submatix

T0024    Azimuth (new)

T0025  Megalodon

T0026 nspiration

specials on request

Schutzüberzüge Atemganitur, Cordura

protection for breathing loop, cordura with velcro

mit Klettverschluss

25,- €    Satz (2 Stück, set of 2)
 

Dolphin back in stock!!!

3/8 UNF thread

opens around 15 bar

25,- Euro

4 Digit   Digital Pressure Gage

perfect for mixing gas

o-ring sealed (IP65)

+/- 0,25% full scale accurancy

Range: 0-5000 psi (0-340 bar)

bar, psi or kg/cm²

housing stainless steel

fitting 1/4 NPT

250 Euro,- (O2 clean of course)

The nut is straight compared to the conical shape of the original, so easy to fix a HUD, the outer shape can be changed, we can make a nut for you or what ever you may need.

16,- Euro

example with nut. Of course fits both sides, no question

automatic bypass unit, with addition thread (if you like) for feeding gas.

Cap and all internals are from Scubapro R190/380

155,- Euro

p-port version

We also provide this house without male p-port, but then the bottom plate has a 2mm hole in the center, that makes is easy to drill your needed hole and glue any fitting you like into the house, or let us know what connection you like and we make it like T0301 ..and others..

it has aprox same high as Dolphin Bypass, diameter is less!

special fitting for Megalodon

190,- Euro

manual gas add (O2 or Dil)

the 9/16 male adapter can be replaced to...what you like...

85,- Euro

one side mal p-port, one side Ray hose connector

one fitting 3/8 UNF to inject O2 or...what ever...

180,- Euro

same shape  as sensor house H0620

Internals are same as T0300

for 1 or 2 cells AA (Mignon 1,5V or 3,6V)

2 cable glands

This is a sample...other styles are possible....

65,- Euro

customer wish sizes.....

This modell shown was made to store a "SPOT" satellite finder and a small mobile phone

we make it for variuos GPS, cell phones, finders...

just let us know which dimensions you need/like

starts at 100 Euro